Connecting (And Using) High-Capacity Batteries in Parallel

-

For those willing to put some elbow grease into it, there is an almost unlimited supply of 18650 lithium ion batteries around for cheap (or free) just waiting to be put into a battery pack of some sort. Old laptop and power tool batteries are prime sources, as these often fail because of one bad cell while the others are still perfectly usable. [limpkin] built a few of these battery packs and now that he’s built a few, he’s back with a new project that allows him to use four custom packs simultaneously.

The problem with using different battery packs in parallel is that unless the batteries are charged to similar voltages, they could generate a very high and potentially dangerous amount of current when connected in parallel. This circuit board, powered by a small ATtiny microcontroller, has four XT-60 connectors for batteries and a fifth for output. It then watches for current draw from each of the batteries and, using a set of solid-state relays, makes sure that no dangerous overcurrent conditions occur if the batteries are connected with mismatched voltages. The code for the microcontroller is available on this GitHub page as well.

Using an array of batteries with a balancing system like this has a number of uses, from ebikes to off-grid power solutions, and of course if you build your own packs you’ll also want to build a cell balancer of some sort as well. Batteries go outsidelectrical e the realm of theory and into that of chemistry, so we’ll also provide a general warning about working in potentially dangerous situations without specialized knowledge, but you can see how [limpkin] built his original packs here if you want to take a look at one person’s strategy for repurposing old cells.



from Blog – Hackaday https://ift.tt/hprdPc5

Comments

Post a Comment

Popular posts from this blog

Modern Radio Receiver Architecture: From Regenerative to Direct Conversion

-
Image
Modern radio receivers have a distinct advantage over the common early designs which I covered in my previous article . Most of the receivers you will have worked with over the past couple decades are designs by Edwin Armstrong ; regenerative, superregenerative, or most commonly superheterodyne. These are distinguished by a few fascinating key traits that bring both benefits and drawbacks. Today let’s dive into Mr. Armstrong’s receivers. I’ll also talk about DC receivers which, despite the name, are not made to listen to batteries. These are receivers you are much more likely to encounter in modern equipment. Regenerative and Superregenerative The regenerative receiver is all about doing more with less. You still see some of these in simple applications like RF remote controls. The idea derives from how an oscillator works. In a simple way of thinking, an oscillator is an amplifier with enough positive feedback that any tiny signal at the right frequency will amplify and then, throu...
Get this one»

Hackaday Links: May 31, 2020

-
We begin with sad news indeed as we mark the passing of Marcel van Kervinck on Monday. The name might not ring a bell, but his project, the Gigatron TTL computer , certainly will. We did a deep dive on the microprocessor-less computer a while back, and Marcel was a regular at conferences and on the Gigatron forums, supporting users and extending what the computer can do. He was pretty candid about his health issues, and I’ll add that when I approached him a few weeks ago out of the blue about perhaps doing a Hack Chat about Gigatron, he was brutally honest about how little time he had left and that he wouldn’t make it that long. I was blown away by the grace and courage he displayed. His co-conspirator Walter Belger will carry on the Gigatron mission, including joining us for a Hack Chat on June 24. In the meantime, this might be a great time to pick up a Gigatron kit before they’re all sold out and get busy soldering all those delicious through-hole TTL chips. May of 2020 is the mo...
Get this one»

Homebrew 68K Micro-ATX Computer Runs Its Own OS

-
Image
We’re no stranger to home built Motorola 68000 computers here at Hackaday, but more often than not, they tend to be an experiment in retro minimalism. The venerable processor is usually joined by only a handful of components, and there’s an excellent chance they’ll have taken up residence on a piece of perfboard. Then [NotArtyom] sent in his Blitz , and launched the bar into the stratosphere. Make no mistake, the Blitz isn’t just some simple demo of classic chips. The open hardware motherboard has onboard floppy, IDE, and PS/2 interfaces, with a trio of 8-bit ISA expansion slots for good measure. The  Motorola 68030 CPU is humming along at 50 MHz, with 4 MB of RAM and 512 KB of ROM along for the ride. Designed to fit the Micro-ATX motherboard standard, you can even mount the Blitz in a contemporary PC case and run it on a standard ATX power supply. An earlier prototype of the Blitz motherboard. As if the hardware wasn’t impressive enough, [NotArtyom] went ahead and created hi...
Get this one»