Retrotechtacular: TOPS Runs the 1970s British Railroad

-

How do you make the trains run on time? British Rail adopted TOPS, a computer system born of IBM’s SAGE defense project, along with work from Standford and Southern Pacific Railroad. Before TOPS, running the railroad took paper. Lots of paper, ranging from a train’s history, assignments, and all the other bits of data required to keep the trains moving. TOPS kept this data in real-time on computer screens all across the system. While British Rail wasn’t the only company to deploy TOPS, they were certainly proud of it and produced the video you can see below about how the system worked.

There are a lot of pictures of old big iron and the narrator says it has an “immense storage capacity.”  The actual computers in question were a pair of IBM System/370 mainframes that each had 4 MB of RAM. There were also banks of 3330 disk drives that used removable disk packs of — gasp — between 100 and 200 MB per pack.

As primitive and large as those disk drives were, they pioneered many familiar-sounding technologies. For example, they used voice coils, servo tracking, MFM encoding, and error-correcting encoding.

The software was written in BAL, the IBM assembly language, although there were a set of macros called TOPSTRAN to make it slightly easier. Originally, each depot was going to get an IBM card reader and punch machine, but these proved to be unreliable in the rugged environment. Instead, each depot had an emulated card reader and punch using a Datapoint 2200 — the famous computer that didn’t use the Intel 8008, but that CPU was made for use in this computer.

In the video, you can see some Datapoint 2200s and card readers in use back at the data center. They even take the cover off one of the Datapoints around the 3-minute mark. The machines had 12K of RAM (on three circuit cards) and two tape drives. Around the 24-minute mark you get a look at a 600 baud, although the railroad apparently only used 200 baud for reliability. They also show a 2,400 baud modem that, we are pretty sure, had to be tuned before use.

The video can’t seem to decide if it is for general audiences or technical people. For example, it describes the tones from the modem and shows block diagrams of many of the systems. There are even some fake oscilloscope traces of modem outputs.

As far as we can tell, some of TOPS is still in use today. We hope some of it has been modernized, though. If you like 1970s mainframes, we’ll go ahead and waste the rest of your day. No kidding. The video doesn’t embed, but you can play it by clicking the picture below.

 

 



from Blog – Hackaday https://ift.tt/cVIrsQA

Comments

Post a Comment

Popular posts from this blog

Modern Radio Receiver Architecture: From Regenerative to Direct Conversion

-
Image
Modern radio receivers have a distinct advantage over the common early designs which I covered in my previous article . Most of the receivers you will have worked with over the past couple decades are designs by Edwin Armstrong ; regenerative, superregenerative, or most commonly superheterodyne. These are distinguished by a few fascinating key traits that bring both benefits and drawbacks. Today let’s dive into Mr. Armstrong’s receivers. I’ll also talk about DC receivers which, despite the name, are not made to listen to batteries. These are receivers you are much more likely to encounter in modern equipment. Regenerative and Superregenerative The regenerative receiver is all about doing more with less. You still see some of these in simple applications like RF remote controls. The idea derives from how an oscillator works. In a simple way of thinking, an oscillator is an amplifier with enough positive feedback that any tiny signal at the right frequency will amplify and then, throu...
Get this one»

Hackaday Links: May 31, 2020

-
We begin with sad news indeed as we mark the passing of Marcel van Kervinck on Monday. The name might not ring a bell, but his project, the Gigatron TTL computer , certainly will. We did a deep dive on the microprocessor-less computer a while back, and Marcel was a regular at conferences and on the Gigatron forums, supporting users and extending what the computer can do. He was pretty candid about his health issues, and I’ll add that when I approached him a few weeks ago out of the blue about perhaps doing a Hack Chat about Gigatron, he was brutally honest about how little time he had left and that he wouldn’t make it that long. I was blown away by the grace and courage he displayed. His co-conspirator Walter Belger will carry on the Gigatron mission, including joining us for a Hack Chat on June 24. In the meantime, this might be a great time to pick up a Gigatron kit before they’re all sold out and get busy soldering all those delicious through-hole TTL chips. May of 2020 is the mo...
Get this one»

Homebrew 68K Micro-ATX Computer Runs Its Own OS

-
Image
We’re no stranger to home built Motorola 68000 computers here at Hackaday, but more often than not, they tend to be an experiment in retro minimalism. The venerable processor is usually joined by only a handful of components, and there’s an excellent chance they’ll have taken up residence on a piece of perfboard. Then [NotArtyom] sent in his Blitz , and launched the bar into the stratosphere. Make no mistake, the Blitz isn’t just some simple demo of classic chips. The open hardware motherboard has onboard floppy, IDE, and PS/2 interfaces, with a trio of 8-bit ISA expansion slots for good measure. The  Motorola 68030 CPU is humming along at 50 MHz, with 4 MB of RAM and 512 KB of ROM along for the ride. Designed to fit the Micro-ATX motherboard standard, you can even mount the Blitz in a contemporary PC case and run it on a standard ATX power supply. An earlier prototype of the Blitz motherboard. As if the hardware wasn’t impressive enough, [NotArtyom] went ahead and created hi...
Get this one»